HILLSBORO, Oregon and SANTA CLARA, California, April 10, 2001 –
Endeavor Intertech Corporation, an innovative developer of high
performance processors, co-simulation interfaces and tools for hardware
and software verification, and DSP Group, Inc. (NASDAQ: DSPG), a leading
developer and marketer of high-performance, cost-effective, licensable
digital signal processing cores, today announced the release of Precyse
Palm™ processor model and CoOperate™ HDL simulator interface for DSP
Group's PalmDSPCore® DSP architecture. Together, these two products
provide co-simulation capabilities that rival other conventional
co-simulation products on the market for as little as 20% of the cost of
traditional per-seat licenses.

Endeavor Intertech's Precyse Palm is a cycle-precise, high performance
DSP model, which can be licensed by itself as a software developer's tool,
or together with CoOperate as a co-simulation tool. By itself, Precyse
Palm executes about 120,000 operations per second, while maintaining bus,
pin, and clock cycle uniformity with the hardware. Moreover, it does so
for each of the eight busses as well as the powerful parallel
instruction-set that make up the PalmDSPCore architecture.

"The unique requirements of algorithm design on a powerful DSP like
PalmDSPCore necessitate an accurate model—otherwise the timing of critical
loops might be left in question," said Dan Budge, Chief Technology Officer
of Endeavor Intertech. "The complexity of the PalmDSPCore made it
imperative that we fully verify our Precyse model against the golden RTL
results—for both functionality and timing. Software developers can have
the confidence of knowing this model is 100% cycle-accurate, and will
simulate loop and other critical sections of code precisely as the
hardware will."

CoOperate transforms the Precyse Palm DSP processor model into a
co-simulating model. This co-simulating model can be easily incorporated
into a hardware design to provide instant co-simulation, without adding
yet another tool to the tool chain. CoOperate provides full
synchronization between the Precyse model and the HDL simulator, while
supplying a high throughput communication pipeline between the two.
CoOperate enables multiple instantiations of the model in a design, offers
full symbolic debugging capability through DSP Group's own symbolic
debugger interface, and connects to most popular Verilog and VHDL hardware
simulators.

"With Endeavor's PalmDSPCore products, software development can be
brought into parallel with the hardware development," said Eyal
Ben-Avraham, DSP Group's VP of Development Tools & Software Support.
"Both development teams are guaranteed the same correct results, because
they can use the same model. The accuracy of the model allows the hardware
team to co-verify with additional intellectual property in the design. The
speed of the model enables the software team to develop drivers and test
unmodified applications. The result is a market-ready product in less
time."

PalmDSPCore designers who seek a cost effective, simple-to-use
co-simulation solution will find CoOperate and Precyse Palm well suited to
their needs. Together, the two tools enable co-simulation with performance
of about 1500 cycles per second, when fully communicating with a hardware
simulator.

PalmDSPCore is the top-of-the-line generation of DSP Group's licensable
cores in the company's SmartCores™ family. Its target markets are third
generation (3G) cellular handsets, broadband communication devices, Voice
over IP gateways and consumer multimedia products. The PalmDSPCore, a
fully synthesizable 'soft core', is process-independent and can be easily
implemented using any ASIC and process libraries.

PalmDSPCore is a low-power consumption processor implementing dual MAC
parallel architecture that has seven computation units working in
parallel. It has three instruction-set categories of single, parallel and
multi-parallel instructions, providing cutting-edge DSP performance, such
as 2 cycles for complex FFT butterfly, while maintaining a very condense
program size.

Endeavor Intertech's Precyse Palm models are available immediately on
Windows, Linux and Sun workstations. CoOperate for the PalmDSPCore can be
bundled with Precyse Palm. Please contact Endeavor for more information on
the cost of the products.

About Endeavor Intertech Corporation

Endeavor Intertech specializes in high performance processor models,
co-simulation interfaces and tools for hardware and software verification.
Endeavor Intertech has been in the business of developing EDA tools and
models since 1997, and has quietly established itself as an innovative
solution provider for its EDA and processor design customers. Endeavor
creates models for DSP, VLIW, RISC, and other embedded cores and
processors. For more information on Endeavor Intertech's Precyse and
CoOperate models and other hardware/software verification tools, please
contact your Endeavor Intertech representative at [email protected], or
1-503-628-6200 x100. Additional information is available on the web at
http://www.endeav.com

About DSP Group, Inc.

DSP Group, Inc., is a global leader in the development and marketing of
high-performance, cost-effective, licensable digital signal processing
cores. DSP Group's family of DSP cores provides ideal solutions for
low-power cost-driven applications such as cellular, broadband
communication, VoIP, multimedia, advanced telecommunication systems, disk
drive controllers and many other types of embedded control applications.
By combining its DSP core technologies with its proprietary advanced
speech-processing algorithms, DSP Group also delivers a wide range of
enabling and application-specific ICs for full-featured integrated
telephony products and digital cordless applications. DSP Group, Inc.,
maintains an international presence with offices located around the globe.
Additional information is available on the web at: http://www.dspg.com

Statements contained in this release may constitute forward-looking
statements. These statements involve certain risks and uncertainties such
as acceptance of the company's new products by existing OEM customers,
potential customers and the company's ability continue to add licensees
and to develop and produce its new products at competitive costs. These
factors and other factors which may effect future operating results or our
stock price are discussed under "FACTORS AFFECTING FUTURE OPERATING
RESULTS' in our report on Form 10-Q for the quarter ended September 30,
2000, which has been filed with the Securities and Exchange Commission and
is also available on our website (www.dspg.com) under Investor
Relations.

Precyse, Precyse Palm and CoOperate are trademarks of Endeavor
Intertech Corporation.

PalmDSPCore and SmartCores are registered or non-registered trademarks
of DSP Group, Inc.

Other brands and products referenced herein are the trademarks or
registered trademarks of their respective holders.